Grundfos pumps
Order Now
GRUNDFOS SCALA 2
SCALA2 incorporates integrated speed control enabling the keeping of the perfect pressure at the taps, meaning that the pump performance will increase with increasing demand.
SCALA2 can be installed in three easy steps:
1. Connect the pipes. 2. Prime the pump. 3. Plug the pump into the power outlet and the pump will start.
Grundfos SCALA2 has all the components necessary to ensure a comfortable pressure:
intelligent controller
integrated speed-controlled drive
integrated tank
integrated sensors
integrated non-return valves.
GRUNDFOS ALPHA 2
GRUNDFOS ALPHA2 is the new generation of small circulation pumps in the highest energy class “A”. The ALPHA2 circulator is the youngest and most innovative member of the family of high quality Grundfos circulators. The use of these pumps is to circulate water in heating systems and in hot water systems.
The circulator pump meets the requirements of the EuP directive.
AUTOADAPT function
In the case of the ALPHA2 pump, there are no concerns about the complicated settings and adjustment of the pump. If you leave the factory settings for AUTOADAPT, the pump automatically analyzes the heating system, searches for the optimal settings and adapts to the requirements and changes to heat. For a more detailed description of the AUTOADAPT function, refer to the enclosed catalog sheet. The AUTOADAPT function can be deactivated by selecting another mode (proportional or constant pressure or conventional three-speed operation).
GRUNDFOS SBA 3-35 A
SBA 3-35 A
The SBA is a complete all-in-one submersible booster pump for pumping clean water, it is especially suitable for rainwater application and small private wells. The SBA comes with an integrate control unit, eliminating the need for an external pump controller.
Specifications
Pumped liquid: Water
Liquid temperature range: 0 .. 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP 60
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Rated flow: 60m³/h
Shaft seal for motor: CER/CARNBR
Approvals on nameplate: CE,GOST2
Curve tolerance: ISO9906:2012 3B
Motor version: T40
GRUNDFOS SP46
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP 30
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Rated flow: 30m³/h
GRUNDFOS SP17
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Rated flow: 17m³/h
Shaft seal for motor: HM/CER
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
GRUNDFOS SP 14
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Rated flow: 14m³/h
Shaft seal for motor: LIPSEAL
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
GRUNDFOS SP11
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP9
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP7
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP5A
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP3A
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS SP2A
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2900 rpm
Rated flow: 2 m³/h
Shaft seal for motor: LIPSEAL
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
GRUNDFOS UNILIFT AP 35
The Grundfos AP submersible effluent pump with great performance.
Suitable for pumping surface water, groundwater, wastewater and similar with impurities up to a diameter of 35 mm.
The pump is equipped with a circular stand and a handle. The pump is supplied with a 10 m electric cable and a float switch for automatic “start/stop”.
Usage
Draining rainwater or drainage water, wastewater from showers, washing machines, sinks.
The AP pump also drains water from pools or rainwater for use in gardening.
Features
Power supply 230 V with 10 m cable
Simple installation
Stainless steel
Single-phase protection (no additional motor protection required)
Grundfos UNILIFT AP 35B
The Grundfos AP submersible effluent pump with great performance.
Suitable for pumping surface water, groundwater, wastewater and similar with impurities up to a diameter of 35 mm.
The pump is equipped with a circular stand and a handle.
The pump is supplied with a 10 m electric cable and a float switch for automatic “start/stop”.
Usage
Draining rainwater or drainage water, wastewater from showers, washing machines, sinks. The AP pump also drains water from pools or rainwater for use in gardening.
Features
Power supply 230 V with 10 m cable
Simple installation
Stainless steel
Single-phase protection (no additional motor protection required)
GRUNDFOS CM10
Applications CM BASIS
CM/CME are reliable, quiet and compact horizontal end-suction pumps
The pumps are suitable for liquid transfer in
Air-conditioning
Domestic water supply and rain water
Heating
Industrial applications
Pressure boosting
Specification s
Pumped liquid: Water
Liquid temperature range: -20 .. 90 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS CM5
Applications CM BASIS
CM/CME are reliable, quiet and compact horizontal end-suction pumps.
The pumps are suitable for liquid transfer in
Air-conditioning
Domestic water supply and rain water
Heating
Industrial applications
Pressure boosting
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 90 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS CM3
Applications CM BASIS
CM/CME are reliable, quiet and compact horizontal end-suction pumps.
The pumps are suitable for liquid transfer in
Air-conditioning
Domestic water supply and rain water
Heating
Industrial applications
Pressure boosting
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 90 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
GRUNDFOS CR90
GRUNDFOS CR 90 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Pumped liquid: WaterLiquid temperature range: -30 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2899 rpm
Rated flow: 90m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR64
GRUNDFOS CR 64 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Pumped liquid: WaterLiquid temperature range: -30 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2899 rpm
Rated flow: 64m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR45
GRUNDFOS CR 45 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2899 rpm
Rated flow: 45m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR32
GRUNDFOS CR32 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2899 rpm
Rated flow: 30 m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR20
GRUNDFOS CR 20 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2899 rpm
Rated flow: 21 m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR15
GRUNDFOS CR15 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2757 rpm
Rated flow: 17 m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR10
GRUNDFOS CR10 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
Specifications
Pumped liquid: Water
Liquid temperature range: -20 .. 120 °C
Liquid temp: 20 °C
Density: 998.2 kg/m³
Technical:
Speed for pump data: 2757 rpm
Rated flow: 10 m³/h
Shaft seal: HQQE
Approvals on nameplate: CE,TR
Curve tolerance: ISO 9906:1999 Annex A
GRUNDFOS CR 5
GRUNDFOS CR5 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
APPLICATION
Commercial air conditioning.
Commercial fire protection.
Commercial heating.
Commercial water pressure boosting.
District cooling.
District heating.
Drinking water treatment.
Irrigation.
Features and benefits
Reliability
High efficiency
Service-friendly
Space-saving
Suitable for slightly aggressive liquids
GRUNDFOS CR3
GRUNDFOS CR3 Vertical, multistage centrifugal pump with suction and discharge ports on the same level. The pump head and base are in cast iron – all other wetted parts are in stainless steel (EN 1.4301)A cartridge shaft seal ensures high reliability, safe handling and easy service and access. Power transmission is via a split coupling. Pipework connection is via oval flanges with internal Rp threads.
APPLICATION
Commercial air conditioning.
Commercial fire protection.
Commercial heating.
Commercial water pressure boosting.
District cooling.
District heating.
Drinking water treatment.
Irrigation.
Features and benefits
Reliability
High efficiency
Service-friendly
Space-saving
Suitable for slightly aggressive liquids
Dayliff Pumps
Order Now
DAYLIFF DBH
The Dayliff DBH2/DBH4/DBH8 range of horizontal multistage centrifugal pumps are designed for continuous duty in various water transfer duties with particular application in pumping slightly corrosive liquids. The pump has small physical dimensions, axial suction port and radial discharge and is base plate mounted. The pump body, suction and discharge ports are made from AISI 316 stainless steel as is all the other parts in contact with the pumped liquid. The mechanical seal is made from silicon carbide designed for easy replacement. Both pump and continuously rated motor unit are of monoblock design and particular attention has been paid to quietness and smooth operation.
DAYLIFF DB12
The DAYLIFF DB12 range of horizontal multistage centrifugal pumps are commercial quality products designed for continuous duty in various water transfer applications. The pump has small physical dimensions, axial suction port and radial discharge port and is base plate mounted. Suction chamber and pump head are made of grey cast iron, the impeller and impeller housing of stainless steel.
Both pump and continuously rated motor unit are of monoblock design, and particular attention has been paid to quietness and smooth operation.
DB12-30
DB12-50
DAYLIFF DB8
The DAYLIFF DB8 range of horizontal multistage centrifugal pumps are commercial quality products designed for continuous duty in various water transfer applications. The pump has small physical dimensions, axial suction port and radial discharge port and is base plate mounted. Suction chamber and pump head are made of grey cast iron, the impeller and impeller housing of stainless steel.
Both pump and continuously rated motor unit are of monoblock design, and particular attention has been paid to quietness and smooth operation.
DB8-30
DB8-50
DAYLIFF DB4
The DAYLIFF DB4 range of horizontal multistage centrifugal pumps are designed for continuous duty in various water transfer applications. The pump has small physical dimensions, axial suction port and radial discharge port and is base plate mounted. Suction chamber and pump head are made of grey cast iron, the impeller and impeller housing of stainless steel.
Both pump and continuously rated motor unit are of monoblock design, and particular attention has been paid to quietness and smooth operation.
DB4-30
DB4-40
DB4-60
DAYLIFF DI/DIN20
The DAYLIFF DI/DIN20 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN20-3(4kw 5.5hp)
DI/DIN20-5(5.5kw 7.5hp)
DI/DIN20-7(7.5kw 10hp)
DI/DIN20-10(11kw 15hp)
DI/DIN20-14(15kw 20hp)
DI/DIN20-17(18.5kw 25hp)
DAYLIFF DI/DIN15
The DAYLIFF DI/DIN 16 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN15-3(3kw 4hp)
DI/DIN15-5(4kw 5.5hp)
DI/DIN15-7(5.5kw 7.5hp)
DI/DIN15-9(7.5kw 10hp)
DI/DIN15-14(11kw 15hp)
DI/DIN15-17(15kw 20kw)
DAYLIFF DI/DIN10
The DAYLIFF DI/DIN 10 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN10-4(1.5kw 2hp)
DI/DIN10-6(2.2kw 3hp)
DI/DIN10-9(3.0kw 4hp)
DI/DIN10-12(4kw 5.5hp)
DI/DIN10-16(5.5kw 7.5hp)
DI/DIN10-22(7.5kw 10hp)
DAYLIFF DI/DIN5
The DAYLIFF DI/DIN5 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN5-5(0.75kw 1hp)
DI/DIN5-8(1.1kw 1.5hp)
DI/DIN5-10(1.5kw 2hp)
DI/DIN5-16(2.2kw 3hp)
DI/DIN5-29(3kw 4hp)
DI/DIN5-36(5.5kw 7.5hp)
DAYLIFF DI/DIN3
The DAYLIFF DI/DIN3 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN3-10(0.75kw 1hp)
DI/DIN3-15(1.1kw 1.5hp)
DI/DIN3-19(1.5kw 2hp)
DI/DIN3-29(2.2kw 3hp)
DI/DIN3-36(3kw 4hp)
DAYLIFF DI/DIN1
The DAYLIFF DI/DIN1 pump range are of non self priming vertical multistage in-line centrifugal design suitable for a wide range of water supply, irrigation, liquid transfer and boosting applications. The pumps are of heavy duty construction and designed for continuous duty in commercial and industrial installations. All DIN pumps feature AISI 316 stainless steel vital components in contact with water including the impellers, intermediate chambers, shaft and top and bottom housings and are suitable for pumping highly mineralised corrosive water. DI pumps feature cast iron top and bottom housing and other components are AISI 304 stainless steel. All pumps are water lubricated and are provided with a standard cartridge type mechanical seal. They are supplied complete with BSP internally threaded counter flanges.
DI/DIN1-23(1.1kw 1.5hp)
DI/DIN1-30(1.5kw 2hp)
DI/DIN1-36(2.2kw 3hp)
DAYLIFF DS17
DAYLIFF DS17 submersible pumps are designed specifically for borehole supply applications. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS17-7(4kw 5.5hp)
DS17-10(5.5kw 7.5hp)
DS17-13(7.5kw 10hp)
DS17-170(9.2kw 12.5hp)
DS17-20(11kw 15hp)
DS17-24(15kw 20hp)
DS17-27(15kw 20hp)
DAYLIFF DS14
DAYLIFF DS14 pumps are designed for a wide range of uses with a particular application to borehole supply. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS14-7 (2.2kw 3hp)
DS14-13(4kw 5.5hp)
DS14-18(5.5kw 7.5hp)
DS14-25(7.5kw 10hp)
DAYLIFF DS 8
DAYLIFF DS 8 submersible pumps are designed specifically for borehole supply applications. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS8-10(1.5kw 2hp)
DS8-15(2.2kw 3hp)
DS8-25(4.0kw 5.5hp)
DS8-30(5.5kw 7.5hp)
DS8-37(7.5KW 10hp)
DS8-44(7.5kw 10hp)
DS8-66(11kw 15hp)
DAYLIFF DS 5
DAYLIFF DS5 submersible pumps are designed specifically for borehole supply applications. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS5-8(0.75kw 1hp)
DS5-12(1.1kw 1.5hp)
DS5-17(1.5Kw 2hp)
DS5-25(2.2kw 3hp)
DS5-33(3.0kw 4hp)
DS5-44(4.0kw 5.5hp)
DS5-60(5.5kw 7.5hp
DAYLIFF DS 3
DAYLIFF DS 3 submersible pumps are designed specifically for borehole supply applications. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS3 -9(0.55kw 0.75hp)
DS3-12(0.75kw 1hp)
DS3-18(1.1kw 1.5hp)
DS3-25 (1.5kw 2hp)
DS3-33 (2.2kw 3hp)
DS3-45 (3kw 4hp)
DS3-60 (4kw 5.5hp)
DAYLIFF DS 2
DAYLIFF DS 2 submersible pumps are designed specifically for borehole supply applications. They are of multistage centrifugal impeller design and all parts are made from stainless steel with water lubricated rubber bearings. A submersible motor is fitted beneath the pump and suction is effected through a strainer between the pump and motor.
DS2-9(0.37kw 0.5hp)
DS 2-13(0.55kw 0.75hp)
DS 2-18 (0.75kw 1hp)
DS 2 -23(1.1kw 1.5hp)
DS 2-33 (1.5kw 2hp)
DS 2-48(2.2kw 3hp)
DS 2-65(3kw 4hp)
DAYLIFF DSP8
The DAYLIFF DSP 8 range of submersible multistage centrifugal pumps are specially designed for borehole supply applications. Material of construction include noryl impellers, glass filled polycarbonate diffusers, stainless steel inlet and outlet chambers, stage casings, shaft and pump housing. These quality materials together with the floating type impeller design provide the pumps with efficient performance ,excellent sand handling capabilities and long life.
DSP 8-8(1.5kw 2hp)
DSP 8-13(2.2kw3hp)
DSP 8-17(3kw 4hp)
DSP 8-23(4kw5.5hp)
DSP 8-32(5.5kw 7.5hp)
DAYLIFF DSP5
The DAYLIFF DSP5 range of submersible multistage centrifugal pumps are specially designed for borehole supply applications. Material of construction include noryl impellers, glass filled polycarbonate diffusers, stainless steel inlet and outlet chambers, stage casings, shaft and pump housing. These quality materials together with the floating type impeller design provide the pumps with efficient performance ,excellent sand handling capabilities and long life.
DSP 5-12(1.1kw 1.5hp)
DSP 5-16(1.5kw 2hp)
DSP5-24(2.2kw 3hp)
DSP5-32(3kw 4hp)
MOTOR
DAYLIFF DSP3
The DAYLIFF DSP3 range of submersible multistage centrifugal pumps are specially designed for borehole supply applications. Material of construction include noryl impellers, glass filled polycarbonate diffusers, stainless steel inlet and outlet chambers, stage casings, shaft and pump housing. These quality materials together with the floating type impeller design provide the pumps with efficient performance ,excellent sand handling capabilities and long life.
DSP3-11( 0.75kw1hp)
DSP3-16(1.1kw 1.5hp)
DSP3-21(1.5kw 2hp)
DSP3-32(2.2kw 3hp)
MOTOR
DAYLIFF DSP1
The DAYLIFF DSP1 range of submersible multistage centrifugal pumps are specially designed for domestic and small scale water supply from wells and boreholes. Material of construction include Noryl impellers, glass filled polycarbonate diffusers, stainless steel inlet and outlet chambers, stage casings, shaft and pump housing. These quality materials together with the floating type impeller design provide the pumps with efficient performance excellent sand handling capabilities and long life.
DSP1-10 (0.37kw 0.5hp)
DSP 1-15(0.55kw0.75hp)
DAYLIFF DSD3
Dayliff DSD 3 range of Submersible Multistage centrifugal pumps are specially designed for domestic and small scale water supply from wells and boreholes. Material of construction include polycarbonate impellers and diffusers, cast iron delivery and suction chambers and AISI 304 stainless steel pump housing, shaft and shaft coupling. These quality materials together with the polycarbonate impellers provide the pumps with excellent sand handling capabilities for a longer life. DSD 3/7, 3/10, 3/13 and 3/18 are supplied complete with 30m cable and control box.
Motor
The pump is coupled to a sealed liquid cooled 2-pole asynchronous squirrel-cage motor constructed of stainless steel. Single phase motors should be supplied with purpose designed Dayliff SCM control boxes for operation and protection against overload, dry running and over/under voltage. Three phase motors require a remote DOL starter; A DAYLIFF SCT electronic Pump Controller is recommended for comprehensive pump control including low level, motor overload and irregular power supply protection.
DAYLIFF DHF
The Dayliff DHF series is a centrifugal non self priming closed impeller pump specially designed for high flow commercial and industrial water supply uses in water boosting and transfer applications. The pump body is cast iron with a brass impeller.
Enclosure Class: IP44
Insulation Class: F
Speed: 2900rpm
OPERATING CONDITIONS
Pumped Liquids: Thin, clean, chemically non-aggressive liquids with max. sand content of 0.25%
Max. Fluid Temperature: +40º C
Max. Ambient Temperature: +40º C
Max. Suction Lift: 7m at sea level
Dayliff DDS 750
The Dayliff DDS pump is of centrifugal single impeller non-self priming design with a close coupled electric motor and the hydraulic end including the pump body, back plate and impeller are made of 304 stainless steel. They are particularly suitable for drainage, agriculture and industrial application for slightly corrosive liquids or where high level of liquid purity is required.
Enclosure Class: IP54
Insulation Class: F
Voltage: 1x240V
Speed: 2900rpm
Dayliff DDJ
The Dayliff DDJ Centrifugal jet type pumps is specifically designed for all small scale domestic and commercial water supply uses. It features an integral ejector unit to provide highly effective self priming performance. The pump body is made from cast iron, the ejector and impeller from engineering plastic.
Enclosure Class: IP44
Insulation Class: F
Speed: 2900rpm
Voltage:1x240V
OPERATING CONDITIONS
Pumped Liquid: Thin, clean, chemically non-aggressive liquids without solid particles or fibres
Max. Fluid Temperature: +50°C
Max. Ambient Temperature: +40°C
Max. Suction Lift: 9m at sea level
Dayliff DDP
The Dayliff DDP peripheral pump is specially designed for all small scale domestic and commercial water supply uses. It is of high specification peripheral featuring copper windings, a high capacity motor and stainless steel housing inserts to ensure free impeller movement. The pump body is manufactured from cast iron and impeller from brass.
Enclosure Class: IP44
Insulation Class: F
Speed: 2900rpm
Voltage:1x240V
OPERATING CONDITIONS
Pumped Liquid: Thin, clean, chemically non-aggressive liquids without solid particles or fibres
Max. Fluid Temperature: +60°C
Max. Ambient Temperature: +40°C
Max. Suction Lift: 7m at sea level
Wilo Pumps
Order Now
Wilo-HiMulti 5
Product Feature
Low noise – 50dB lower the normal conversation noise 60dB.
High efficiency with inverter technology uo to 33% energy savings.
Completely new design and easy set-up via green button.
Applied engineering plastic with high corrosion resistance to all parts contacting water.
Able to use more safely and economically with remarkable protection action.
Suction is available up to 8 meters.
QFN6-44 WILO 44 STAGE 100MM FOR 4 MOTOR
APPLICATION
For water and drinking water supply from boreholes
and rainwater storage
Process water supply
For municipal water supply, sprinkling and irrigation
Pressure boosting
Lowering the water level
For pumping water in industrial applications
For pumping water without long-fibre and abrasive
constituents
QFN5-18 WILO 18 STAGE 100MM FOR 4 MOTOR
APPLICATION
For water and drinking water supply from boreholes
and rainwater storage
Process water supply
For municipal water supply, sprinkling and irrigation
Pressure boosting
Lowering the water level
For pumping water in industrial applications
For pumping water without long-fibre and abrasive
constituents
QFN5-25 WILO 25 STAGE 100MM FOR 4 MOTOR
APPLICATION
For water and drinking water supply from boreholes
and rainwater storage
Process water supply
For municipal water supply, sprinkling and irrigation
Pressure boosting
Lowering the water level
For pumping water in industrial applications
For pumping water without long-fibre and abrasive
constituents
Wilo Yonos PICO1.0
The Wilo Yonos PICO1.0 circulator is the basic type in a range of economical and highly efficient pumps.
Min. pump power is only 4W! The Yonos Pico pump is used in all common heating systems, air conditioners
and industrial circulation systems . Other suitable applications for the use of the pump are family houses
and semi-detached houses. The pump allows both manual and automatic operation (see below).
The pump meets the requirements of the ErP directive.
Automatic functions
Continuous power adjustment depending on operating mode
Automatic unlocking
Manual functions
Operating mode setting
Pump power setting
Venting function
WILO TS40/10/A 1-230-50-2-10MKA
WILO TS 40
Submersible drainage pump
Application
Pumping of
Sewage without faeces and long- fibre components
Wastewater
Volume flow Qmax 18 m³/h
Delivery head Hmax 14m
Technical data
Mains connection: 1~230 V, 50 Hz or
3~400 V, 50 Hz
Immersed operating mode: S1
Non-immersed operating mode: S3
25 %
Max. immersion depth: 5 m
Fluid temperature: max. 35 °C
WILO HICONTROL 1
Electronic, fully automatic pressure guard and a flow switch. Supplied
in “in-line” with input and output in the vertical axis with individual G 1″ connecting threads.
Functions
HiControl 1 automatically switches the pump on or off when opening or closing the water tap.
Another important feature of the switch is dry run protection in case of insufficient water inflow,
excessive suction height and leakage of piping.
Features
Switching pressure 1.5 bar
Compact construction and simple assembly
No-noise operation
Integrated water pump protection
High reliability
Indications of operating conditions
HiControl is the successor of the original type with the name Fluidcontrol.
WILO SPU4‐02
General information
Wilo submersible SPU pumps can also be used
horizontally.
Rubber bearings are water lubricated and have sand channels to
make enable the sand particles leave the pump with the pumped
liquid.
The stainless steel strainer prevents particles
over a certain size from entering the pump.
WILO SPU4-01
General information
Wilo submersible SPU pumps can also be used
horizontally.
Rubber bearings are water lubricated and have sand channels to
make enable the sand particles leave the pump with the pumped
liquid.
The stainless steel strainer prevents particles
over a certain size from entering the pump.
WILO MHI 1602-1/E/3-400-50-2/1E3
WILO MHI 1602-1/E/3-400-50-2 1.5kw 19kg
Design
Non-self-priming multistage pump
Application
Water supply and pressure boosting
Industrial circulation systems
Process water
Closed cooling circuits
Washing system
Irrigation
Water treatment
Power
Fluid temperature T -15…+110 °C
Max. ambient temperature T 40 °C
Rated pressure PN bar
Inlet pressure max. H 6 bar
Maximum operating pressure pmax 10 bar
WILO MHI MHI 903 -E-1-230-50-2
Applications
Pumps for clear liquids in residential, agricultural, industrial, and other
applications.
– Drawing of water from a well, spring, river, pond, etc. Water should
not be drawn from abyssinian wells (tube, driven well).
Technical description
Permissible temperature range –15 °C to +90 °C
Maximum ambient temperature +40 °C
Maximum permissible working pressure 10 bar
Mains voltages: 50 Hz 60 Hz
1~230V (±10%) 1~220V (-10%) – 1~240V (+6%)
3~230/400V (±10%) 3~220/380V (-10%) – 3~265/460V (+10%)
Speed (RPM) 50 Hz 60 Hz
2900 RPM 3500 RPM
Mains fuse protection see motor rating plate
Protective system IP 54
Insulation class F
Wilo-Economy MHI 803-1/E/3-400-50-2
WILO MHI 803-1/E/3-400-50-2 1.1kw 12.1kg
Design
Non-self-priming multistage pump
Application
Water supply and pressure boosting
Industrial circulation systems
Process water
Closed cooling circuits
Washing system
Irrigation
Water treatment
Power
Fluid temperature T -15…+110 °C
Max. ambient temperature T 40 °C
Rated pressure PN bar
Inlet pressure max. H 6 bar
Maximum operating pressure pmax 10 bar
Wilo MultiPress MP 305 IE3 (3~230/400 V)
MP 305
Design
Non-self-priming multistage centrifugal pumps
Application
• Water supply
• Sprinkling
• Irrigation and spraying
• Rainwater utilisation
Special features/product advantages
• Low-noise
• Ideal as a base-load pump for rainwater utilisation
Technical data
• Mains connection 1~230 V, 50 Hz, 3~400 V, 50 Hz
• Max. inlet pressure of 6 bar
• Fluid temperature max. +5 °C to +35 °C
• Max. ambient temperature of +40 °C
• Max. operating pressure of 10 bar
• Protection class 1~: IP X4; 3~: IP 54
• Pressure-side connections Rp 1
• Suction-side connections: Rp 1 for MP3..;
WILO PB -201EA
Silent pressure pump
Approved fluids: Clean water with no solids
Power Approved fluids: Clean water with no solids
Power source: 230V, 50Hz, Single phase
Max.flowrate: 4.5m³/h
Max. head: 20m
Fluid temperature:0°C to +80°C
Max. working pressure:6bar
Degree of protection IP44
Application
• Pressure boosting
• Storage tank or mains fed water
Advantages
• Stable water pressure due to Flow switch inside of casing
• Inline installation
• Auto/Off/Manual optional operation
• Motor with in-built Thermal Protection
WILO PB-400 EA
Approved fluids: Clean water with no solids Power source: 230V, 50Hz, Single phase Max.flowrate: 4.5m³/h Max. head: 20m Fluid temperature:0°C to +80°C Max. working pressure:6bar Degree of protection IP44 Application
WILO HIPERI HIPERI 1-5
Product Feature
– Rated power P20.55 kW
– Rated current IN3.7 A
– Easy handling due to its lightweight, perfect for continuous operation.
– Brass impeller for fluids up to 60°C and ambient temperature up to 40°C.
– Efficiently thanks to low power consumption with high maximum volume flow.
– Up to 8 meters negative suction head.
– Discharge height max .: 49.7 m
Application
– Water distribution/boosting
– Raw water intake
– Sprinkling and spraying
– Rainwater utilization
WILO PERIPHERAL
Product Feature
– Easy handling due to its light weight, perfect for continous operation.
– Brass impeller for fluids up to 60°C and ambient temperature up to 40°C.
– Efficiently thanks to low power consumption with high maximum volume flow.
– Up to 8 meters negative suction head.
– Discharge height max .: 27 m
Application
– Water distribution/boosting
– Raw water intake
– Sprinkling and spraying
– Rainwater utilization
WILO INITIAL JET 9-4
The self-priming pump with a robust cast iron construction can withstand even more demanding environments. It is used for pumping water from wells, filling, pumping empty, transferring by pumping, irrigation and sprinkling and as emergency pump for overflows. The pumped water may contain sand up to 30 g/m³.
Pedrollo Pumps
Order Now
PEDROLLO D Submersible pumps
PEDERELLO D SUBMERSIBLE PUMPS
PERFORMANCE RANGE
• Flow rate up to 300 l/min (18 m3/h)
• Head up to 26 m
APPLICATION LIMITS
• 5 m maximum immersion depth
(with a sufficiently long power cable)
• Maximum liquid temperature up to +40°C
• Passage of suspended solids up to Ø 10 mm
• Suction down to 17 mm above ground level
• Minimum immersion depth for continuous service:
– 210 mm for D 8-10-20
– 250 mm for D 30
CONSTRUCTION AND SAFETY STANDARDS
• Power cable length:
– 5 m for D 8, D 10, D 20
– 10 m for D 30
• Float switch for single-phase versions
PEDROLLO TOP MULTI PUMPS
PEDRELLO TOP MULTI PUMPS
PERFORMANCE RANGE
• Flow rate up to 120 l/min (7.2 m³/h)
• Head up to 52 m
APPLICATION LIMITS
• Immersion depth:
– up to 3 m for TOP MULTI 1
– up to 10 m for TOP MULTI 2-3-4-5
(with a sufficiently long power cable)
• Maximum liquid temperature +40 °C
• Suction level:
– 25 mm above ground level for TOP MULTI 1
– 35 mm above ground level for TOP MULTI 2-3-4-5
• Continuous service S1
PEDROLLO TOP SERIES DRAINAGE PUMPS
PEDERELLO TOP SERIES PERFORMANCE RANGE
• Flow rate up to 360 l/min (21.6 m3/h)
• Head up to 15.5 m
APPLICATION LIMITS
• Immersion depth:
– up to 3 m for TOP 1-2-3
– up to 5 m for TOP 4-5
(with a sufficiently long power cable)
• Maximum liquid temperature +40 °C
(Maximum liquid temperature +90 °C
for a maximum of 3 minutes intermittent service)
• Passage of suspended solids up to Ø 10 mm
• Suction level:
– 14 mm above ground level for TOP 1-2-3
– 30 mm above ground level for TOP 4-5
• Continuous service S1
CONSTRUCTION AND SAFETY STANDARDS
The pumps are complete with:
– 5 m long power cable for TOP 1-2-3
– 10 m long power cable for TOP 4-5
– float switch
PEDROLLO CPM 158
PEDRELLO CPM 158
Features
Liquid type: Clean Water
Uses: domestic, civil
Applications: irrigation pumps, cooling systems, air conditioning systems,
water supply systems, liquids transfer, pressure systems
typology: surface
Family: centrifugal
Performance Range:
Flow rate up to 160 l/min (9,6 m³/h)
Head up to 36m
Application Limit:
Temperature of the liquid from -10 °C to +90 °C
Ambient Temperature to +40 °C
Manometric suction lift up to 7 m
Max. working pressure:
– 6 bar for CP 100-130-132-150-158
DAB Pumps
Order Now
DAB – E.SYBOX MINI AUTOMATIC BOOSTER SYSTEM WITH INVERTER
Esybox Mini has a different appearance than any other booster set and is small and completely integrated. Once you install and use it, you realize that the real difference is in the comfort and performance.
Esybox Mini uses the most advanced DAB technologies to create constant pressure according to the system demands and thus an optimization of energy consumption.
Suitable for use with potable water, in domestic systems and gardening applications.
SS6 B SERIES
APPLICATIONS
Multistage mixed-flow borehole electric pumps, completely made in stainless steel (AISI 304L or AISI 316 on request), usable for wells from a minimum
diameter equal to pump size or greater and capable of developing a wide range of Flows and Heads.
These pumps can be used in a wide range of lifting, distributing, and pressuring application: domestic and general water supply; sprinkler and drip
irrigations systems; fire-fighting installations; lowering of groundwater level; industrial supplies as mining, hot springs, autoclaves and tanks.
These pumps are suitable both for standard water and for aggressive water applications by choosing the proper manufacturing material (AISI 304L or
AISI 316) both for hydraulic part and motor.
Special version of motors with PE2+PA windings can be used on request for high-temperature water applications up to maximum 50°C.
Pumps can be installed both vertically and horizontally simply by removing the non-return valve and adding a cooling sleeve to the suction case (the
only remark is to check the motor applicability to horizontal operations, refer to the motor specifications section).
SS6A SERIRS
APPLICATIONS
Multistage mixed-flow borehole electric pumps, completely made in stainless steel (AISI 304L or AISI 316 on request), usable for wells from a minimum
diameter equal to pump size or greater and capable of developing a wide range of Flows and Heads.
These pumps can be used in a wide range of lifting, distributing, and pressuring application: domestic and general water supply; sprinkler and drip
irrigations systems; fire-fighting installations; lowering of groundwater level; industrial supplies as mining, hot springs, autoclaves and tanks.
These pumps are suitable both for standard water and for aggressive water applications by choosing the proper manufacturing material (AISI 304L or
AISI 316) both for hydraulic part and motor.
Special version of motors with PE2+PA windings can be used on request for high-temperature water applications up to maximum 50°C.
Pumps can be installed both vertically and horizontally simply by removing the non-return valve and adding a cooling sleeve to the suction case (the
only remark is to check the motor applicability to horizontal operations, refer to the motor specifications section).
DAB S4-16
APPLICATION
S4-16 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-12
APPLICATION
S4-12 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-8
APPLICATION
S4-8 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-6
APPLICATION
S4-6 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-3
APPLICATION
S4 -3 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-2
APPLICATION
S4 -2 are multi-impeller borehole pumps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
DAB S4-1
APPLICATION
S4 -1 are multi-impeller borehole pu wemps with a water-filled or oil-filled DAB motor capable of providing a wide range of hydraulic performances, designed
for water boosting, drawing water from subsoil, gardening and irrigation in civil and commercial applications and for the movement of water in
agriculture.
TECNICAL DATA
Operating range :
Up to 21,6 m3
/h with head up to 427 metres
Type of pumped liquid : Clean, free of solids and abrasive substances,
non-viscous, non-aggressive, non-crystallized and chemically neutral
Pump maximum diameter: 99 mm
Maximum amount of sand: 150 g/m3
Rated flow 1m³/h
DAB 2K TWIN
Water lifting sets particularly suited for small and medium civil systems. The use of K double impeller electric pumps ensures a high power-pressure
ratio, resulting in high performance and extremely quiet operation. Their main features are construction sturdiness, compact sizes, and utmost reliability.
The sets are supplied as standard with tanks and with air supply connector.
Operating range: from 1 to 19 m3
/h.
Pumped liquid: clean, free of solids and abrasives, non
viscous, non aggressive, non crystallised and chemically neutral,
with properties similar to water.
Pumped liquid temperature range: from -10°C to +70°C.
Maximum ambient temperature: +40°C
Maximum operating pressure: PN10
DAB K SINGLE IMPELLER
Single-impeller centrifugal pump suitable for domestic, civil, industrial and agricultural systems, and for decanting, mixing and irrigation uses.
Operating range: from 1,8 to 96 m3/h, with head up to 62 metres.
Maximum operating pressure: K 20/41, K 30/70, K 30/100, K 36/100, K 12/200, K 14/400 : 6 bar (600 kPa), K 36/200, K 40/200, K 55/200, K 11/500, K 18/500, K 28/500 : 8 bar (800 kPa), K 40/400, K 50/400, K 30/800, K 40/800, K 50/800, K 20/1200, K 25/1200, K 35/1200 : 10 bar (1000 kPa)
Installation: horizontal or vertical position, provided that the motor is always above the pump.
Liquid temperature range: K 20/41, K 30/70, K 30/100, K 36/100, K 12/200, K 36/200, K 40/200 : from -10 °C to +50 °C.
Remainder of the range: from -15 °C to +110 °C.
Salmson pumps
Order Now
SALMSON PRIUX HOME M 40-25/180mm
Design
Glandless circulation pump with threaded connection, blocking-current proof EC motor and integrated electronic power control.
Application
All hot water heating systems, air-conditioning applications, industrial circulation systems.
Special features/product advantages
High-efficiency pump especially for single and two-family houses
Only 4 watts minimum power consumption
Pre-selectable control modes for optimum load adjustment Δ p-c (differential pressure constant), Δ p-v (differential pressure variable)
Integrated motor protection
LED display for setting the setpoint and displaying actual consumption in watts
Bleeding function for bleeding the rotor chamber
Quick electrical connection with Salmson-Connector
Flexible installation thanks to compact construction
Very high starting torque for reliable starting
SALMSON SIRIUX HOME 60-25/180mm
APPLICATION
For the accelerated circulation of hot water
in heating circuits with duty point optimisa-
tion for:
• New or old systems (reconditioning
– extension)
• Systems with or without thermostatically
controlled valves
• Single-family houses
• Radiators and underfloor heating systems
• Thermosiphon-type systems
SALMSON SIRIUX HOME 40-32/180mm
APPLICATION
For the accelerated circulation of hot water
in heating circuits with duty point optimisa-
tion for:
• New or old systems (reconditioning
– extension)
• Systems with or without thermostatically
controlled valves
• Single-family houses
• Radiators and underfloor heating systems
• Thermosiphon-type systems
SALMSON SIRIUX 60-15/130mm
APPLICATION
For the accelerated circulation of hot water
in heating circuits with duty point optimisa-
tion for:
• New or old systems (reconditioning
– extension)
• Systems with or without thermostatically
controlled valves
• Single-family houses
• Radiators and underfloor heating systems
• Thermosiphon-type systems
SALMSON SIRIUX HOME 60-32/180MM
APPLICATION
For the accelerated circulation of hot water
in heating circuits with duty point optimisa-
tion for:
• New or old systems (reconditioning
– extension)
• Systems with or without thermostatically
controlled valves
• Single-family houses
• Radiators and underfloor heating systems
• Thermosiphon-type systems
SALMSON Siriux home 40-25 / 130mm
APPLICATION
For the accelerated circulation of hot water
in heating circuits with duty point optimisa-
tion for:
• New or old systems (reconditioning
– extension)
• Systems with or without thermostatically
controlled valves
• Single-family houses
• Radiators and underfloor heating systems
• Thermosiphon-type systems
SALMSON SBS 2 204-0,90 MF
APPLICATION
Domestic or small-scale commercial use
Maximum chlorine content: 150 mg/litre
• Lifting of domestic wastewater, valve water,
water containing sludges and particles, etc
• For housing, garages, car parks, etc
• Draining of boiler room sumps.
• Emptying of cellars and pools.
• Whenever the total head is high (geometric height and distance).
• Drying of cellars and land.
• Discontinuous operation – pump comple-tely submerged
Operating limits
Flows rates up to : 18 m3
/h
Heads up to : 14 m
Temperature range : + 3° to 35°C
Free passage : 10 mm
ND of discharge orifice R11/2
SALMSON SBS 2 204-0,45MF
APPLICATION
Domestic or small-scale commercial use
Maximum chlorine content: 150 mg/litre
• Lifting of domestic wastewater, valve water,
water containing sludges and particles, etc
• For housing, garages, car parks, etc
• Draining of boiler room sumps.
• Emptying of cellars and pools.
• Whenever the total head is high (geometric
height and distance).
• Drying of cellars and land.
• Discontinuous operation – pump comple-tely submerged
OPerating limits
Flows rates up to : 18 m3
/h
Heads up to : 14 m
Temperature range : + 3° to 35°C
Free passage : 10 mm
ND of discharge orifice R11/2
SALMSON SUBSON 620 MFE-SA
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON SUBSON 30 MFP-A
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON SUBSON 20 MF
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON SUBSON 10MF
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON SUBSON AB 30MF
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON SUBSON AB 20MFP
APPLICATION
• Cellar drainage
• Removal of infiltration water
• Drainage of boiler room or basin sumps
• Lift-pumping of wastewater not containing
fats or fibrous materials, originating from:
– washing machine, dishwasher
– wash basin, shower, etc…
SUBSON “A” corrosive water version:
– discharge from water softeners
– seawater
– brackish water
– treated swimming pool water, etc…
SALMSON PRIMA JET SYSTEM 4-4-50
SALMSON PRIMA JET SYSTEM 4-4-50 (50 Litre Tank) is System for water supply, irrigation and rainwater utilisation; consisting of a self-priming pump with up to 7 m, a pressure tank and pressure switch with automatic start/stop function.
Application
Water supply
Sprinkling
Irrigation and spraying
Pumping water from wells and out of tanks lying at greater depths
Equipment/function
Directly flanged motor
Pressure switch
Diaphragm pressure vessel
Single-phase motor
Connection cable with plug
Thermal motor protection switch
SALMSON PRIMA JET SYSTEM 3-4-22
SALMSON PRIMA JET SYSTEM 3-4-22 (20 Litre Tank) is System for water supply, irrigation and rainwater utilisation; consisting of a self-priming pump with up to 7 m, a pressure tank and pressure switch with automatic start/stop function.
Application
Water supply
Sprinkling
Irrigation and spraying
Pumping water from wells and out of tanks lying at greater depths
Equipment/function
Directly flanged motor
Pressure switch
Diaphragm pressure vessel
Single-phase motor
Connection cable with plug
Thermal motor protection switch
SALMSON PRIMA JET 4-4
A LMSON PRIMA JET is a self-priming single-stage jet pump for water supply, irrigation and rainwater utilisation. Self-priming up to 7 m. Electrical connection via a terminal box. All parts that come into contact with fluids are corrosion-resistant.
User-friendly thanks to its low weight and compact dimensions
High supply guarantee due to good hydraulic output, self-priming up to 7 m, even at low flow
Heavy-duty design for long-lasting operation
Suitable Applications
Pumping water from wells
Filling, pumping empty, transferring by pumping, irrigation and sprinkling
As emergency pump for overflows
Equipment/function
Single-phase motor (1~230 V)
Thermal motor protection switch
SALMSON PRIMA JET 3-4
SALMSON PRIMA JET
is a self-priming single-stage jet pump for water supply, irrigation and rainwater utilisation. Self-priming up to 7 m. Electrical connection via a terminal box. All parts that come into contact with fluids are corrosion-resistant.
User-friendly thanks to its low weight and compact dimensions
ALPHA Water Pumps
Order Now
ALPHAR HPS
APPLICATIONS
The ALPHAR HPS range are horizontal design multistage pumps suitable for pressure boosting,water transfer and agricultural application.
CONSTRUCTION FEATURES
Robust cast iron sunction and delivery housing stainless steel impellers diffuser’s and wearings coupled to asycronous 2 pole air cooled squirrel-cage Motor with inbuilt thermal overload protection. The pumps are designed by for efficient and dependable performance and long trouble free life.
ALPHA HP 8
APPLICATIONS
The ALPHAR HP 8 range are horizontal design multistage pumps suitable for pressure boosting,water transfer and agricultural application.
CONSTRUCTION FEATURES
Robust cast iron sunction and delivery housing stainless steel impellers diffuser’s and wearings coupled to asycronous 2 pole air cooled squirrel-cage Motor with inbuilt thermal overload protection. The pumps are designed by for efficient and dependable performance and long trouble free life.
ALPHA BPS 8
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 30 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
SAND CONTENT 50g/m3
ALPHA BPS 5
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 30 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
SAND CONTENT 50g/m3
Technical:
Speed for pump data: 2900 rpm
Rated flow: 5m³/h
ALPHA BPS 3
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 30 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
SAND CONTENT 50g/m3
ALPHA BPS 2
Applications
The Submersible pumps are suitable for liquid transfer in
Domestic water supply and rain water
Groundwater supply
Industrial applications
Specifications
Pumped liquid: Water
Maximum liquid temperature: 30 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
SAND CONTENT 50g/m3
Commercial Pump Booster Sets
Order Now
GRUNDFOS MULTI E-CM SERIES
GRUNDFOS Hydro Multi-E booster sets are designed for the transfer and pressure boosting of clean water in waterworks, blocks of flats, hotels, industry, hospitals, schools, etc. GRUNDFOS Hydro Multi-E booster set consists of 2 to 3 CME pumps coupled in parallel and mounted on a common base frame provided with all the necessary fittings.
GRUNDFOS CMBE TWIN BOOSTER SET
The Grundfos CMBE TWIN is a compact twin booster
pump for water supply and boosting commercial
applications. The integrated speed controller enables
the CMBE to maintain a constant pressure in the pipe
system and is mainly used in places such as:
• cluster homes
• apartment buildings
• schools
• small hotels
• small office buildings
• small industrial plants and businesses
• hospitals
The CMBE TWIN Booster system consists of two
CMBE Boosters connected in parallel and mounted
on a common base plate and provide the following
DAB 2 EURO BOOSTER SETS
APPLICATIONS
Water lifting sets particularly suited for domestic use, and small civil, agricultural, or industrial systems. Their main features are utmost reliability, simple
operation, and the fact that no maintenance is required. The sets are supplied as standard with tanks and with air supply connector.
GRUNDFOS MULTI-S CM PRESSURE BOOSTER SETS
PRODUCT DESCRIPTION
GRUNDFOS Hydro Multi-S booster sets are designed for the transfer and pressure boosting of clean water in blocks of flats, hotels, schools, etc.
Hydro Multi-S consists of 2 identical CM pumps connected in parallel and mounted on a common base frame, with a control cabinet with integrated controller and provided with all the necessary fittings. The booster set is fitted with an on/off switch for the supply voltage.
DAB 2K TWIN BOOSTER SET
APPLICATIONS
Water lifting sets particularly suited for small and medium civil systems. The use of K double impeller electric pumps ensures a high power-pressure
ratio, resulting in high performance and extremely quiet operation. Their main features are construction sturdiness, compact sizes, and utmost reliability.
The sets are supplied as standard with tanks and with air supply connector.
Pump Control/ Accessories.
Order Now
QFN25-18 WILO 18 STAGE 100MM FOR 4 MOTOR
APPLICATION
For water and drinking water supply from boreholes
and rainwater storage
Process water supply
For municipal water supply, sprinkling and irrigation
Pressure boosting
Lowering the water level
For pumping water in industrial applications
For pumping water without long-fibre and abrasive
constituents
SOLLATEK AVS 15A
AVS15 micro (Automatic Voltage Switcher 15 Amps) Single Phase-15 Amps
Low power (under-voltage) will damage any refrigeration appliance’s compressor and High Power (Over voltage) will damage any electrical or electronic equipment. The AVS15 is the most complete power protection device combining over-voltage, under-voltage, power-back surges and spikes/surge protection. Additionally, there is a delay when power returns to normal. This will ensure that the appliance is not switched on-off repeatedly during fluctuations nor it is subjected to a massive surge normally experienced when power returns after power cuts.
SOLLATEK AVS 13A
AVS13 micro (Automatic Voltage Switcher 13 Amps) Single Phase-13 Amps
Low power (under-voltage) will damage any refrigeration appliance’s compressor and High Power (Over voltage) will damage any electrical or electronic equipment. The AVS13 is the most complete power protection device combining over-voltage, under-voltage, power-back surges and spikes/surge protection. Additionally, there is a delay when power returns to normal. This will ensure that the appliance is not switched on-off repeatedly during fluctuations nor it is subjected to a massive surge normally experienced when power returns after power cuts.
WILO Hi CONTROL 1
The Wilo HiControl 1 series is used for borehole pumps to enable automatic operation. Wilo-HiControl 1 protects the pump against operation with low volume flow. Thanks to a volume flow sensor and pressure sensor, Wilo-HiControl 1 automates the pump between two values, the start-up pressure and the shut-down volume flow. If the pressure in the network is lower than the start-up pressure, Wilo-HiControl 1 starts the pump. The pump continues to operate until the volume flow falls below the value of the shut-off volume flow.
The interior small container prevents water hammering and cycling.
Wilo-HiControl 1 can be mounted on surface pumps or connected to submersible pumps for domestic water supply.
AUTOMATIC VOLTAGE SWITCHER 3PH
Dayliff power controllers are quality products used in various applications. This includes monitoring the incoming power supply and when outside pre-set limits disconnect the equipment, reconnecting on return of normal power after a start-up delay to protect against damaging power-back surges. The controllers are fitted with LED lights indicating the power status and installation couldn’t be simpler. All controllers offer complete and reliable protection against the damage caused by fluctuating power and are essential accessories for all environments where there is a risk of inconsistent power supply.
AUTOMATIC VOLTAGE SWITCHER 30A
Dayliff power controllers are quality products used in various applications. This includes monitoring the incoming power supply and when outside pre-set limits disconnect the equipment, reconnecting on return of normal power after a start-up delay to protect against damaging power-back surges. The controllers are fitted with LED lights indicating the power status and installation couldn’t be simpler. All controllers offer complete and reliable protection against the damage caused by fluctuating power and are essential accessories for all environments where there is a risk of inconsistent power supply.
AUTOMATIC VOLTAGE SWITCHER 13/15 A
Dayliff power controllers are quality products used in various applications. This includes monitoring the incoming power supply and when outside pre-set limits disconnect the equipment, reconnecting on return of normal power after a start-up delay to protect against damaging power-back surges. The controllers are fitted with LED lights indicating the power status and installation couldn’t be simpler. All controllers offer complete and reliable protection against the damage caused by fluctuating power and are essential accessories for all environments where there is a risk of inconsistent power supply.
DAYLIFF PUMP CONTROLLER S
Press Pump Controller
An in-line electronic pump controller for automatic operation of pressurised water supplies. Features include:-
Starts pump on pressure (fixed at 1.5 Bar) and stops on low flow
Dry run protection provided. Standard models require manual reset, Automatic models restart when supply returns
Incorporates a spring activated hydraulic accumulator to control pump cycling
LED power on, pump run and run dry indicators
Max Motor size: 1.1kW/1ph
Max Current: 10A
Max Operating Pressure: 10Bar
Bar Connection: 1″M
Dimensions (L/W/H): 227x130x168mm (Manual), 210x110x110 (Auto)
Protection: IP54(Auto), IP65 (Manual)
TREVITECH PUMP CONTROLLER S
Trevitech Pump Controllers area revolutionary integrated booster pump control units for the provision of automatic pressurised water supply. They incorporate a combination of hydraulic and electronic control functions, starting the pump when system pressure drops to the pre-set value and stopping the pump when demand drops below the cut-out flow rate. Particular features are:
Automatic pump start and stop as determined by user demand.
Maintenance of constant output pressure.
Pump shutdown in the event of low suction supply or suction blockage.
Attenuates the effects of water hammer.
Control Panels / Accessories
Order NowIntelligent Digital Three Phase Water Pump Control Panel- Auto / Manual , With LCD Displaying
Intelligent Digital Three Phase Water Pump Control Panel- Auto / Manual , With LCD Displaying
Intelligent Digital Three Phase water Pump control panel is a smart and intelligent three phase fully automatic pump controller with built-in water level control .
PROTECTION OFFERED
Dry run
Over load
Transient surge
Under voltage
Over voltage
Open phase
Pump shaft rust protection
Pump stalled
Short circuit
Over temp
Three phase unbalance
Phase reversal
Repeated start
ELECTROMECHANICAL CONTROL PANELS
Electromechanical control panels designed to control one or two submersible single-phase or three-phase electric pumps in water and wastewater applications.
They are provided with a thermal overload protection relay incorporated in the IP55 weather-proof cabinet.
Applications
•Water supply pumps
•Wastewater pumps
•Many more motor control applications
DOL ELECTROMAGNETIC STARTER
Top quality Chint direct online DOL electric motor starter.
Available in single (240V) or three (415V) phase.
Overland Relay available from 1.6 amp to 32 amp.
Starter has a metal base and plastic cover.
IP55 Rated.
Easy to use start / stop buttons.
Please check the FULL LOAD CURRENT rating of your motor before choosing which size you need.
GRUNDFOS MP204
The motor protector MP 204 is an electronic control unit designed for monitoring and protection of motors, pumps, machines, cables and cable joints.
The MP 204 monitors the following parameters:
•System insulation resistance to earth before start
•Motor temperature. Only possible if the motor is fitted with an operational Tempcon temperature transmitter, a Pt100/Pt1000 or a PTC sensor
•Current consumption and unbalance
•Supply voltage
•Phase sequence
•Missing phase
•Power factor (cos phi)
•Harmonic distortion
Solar Equipment & Accessories
Order Now
UltraSun UVR VacRod -150
Particular features of the systems are:-
•Double layered borosilicate glass vacuum tube with clear outer layer and an inner layer specially coated for maximum solar irradiation absorption.
•Storage tank comprising heavy duty stainless steel SU316 inner cylinder with external insulated painted steel casing.
•Aluminium header manifold for heat transfer.
•Anodised aluminium frame.
•Five year guarantee for the tank and heating tubes.
Ultrasun UVR VacRod heaters are highly efficient and effective products designed for various installation conditions including pressurized direct supply and mineralized input water. They are manufactured to the highest standards and will give many years of free hot water and trouble-free operation.
UltraSun Premium 300L Indirect Solar Hot Water System
Features include:-
•Heavy duty tank which includes a steel powder coated outside casing, steel storage tank internally coated with glazed enamel and fitted with a magnesium sacrificial anode for exceptional corrosion protection, UV resistant plastic end caps and a 2kW heating element with thermostat.
•Solar collectors that incorporate full area copper absorption plates ultrasonically welded to copper circulation tubes, high specification insulation and tempered security glass to provide energy absorption of up to 95%.
•Low thermal conductivity high specification flexible stainless steel circulation piping with silver foil coated polystyrene insulation jackets.
Connection piping that includes an incoming non-return valve, pressure release valve rated at 8bar and drain cock. An extra 3bar pressure release valve is provided for the closed loop tank.
•Galvanised mounting frame for both flat or inclined roof installations that ensures high durability in all weather conditions
Ultrasun Premium solar systems are available in various tank sizes and collector configurations to suit domestic and small-scale installation applications. They are efficient and robust products guaranteed for five years to demonstrate the high material speciation. Designed for many years of trouble free operations, they are the ideal solution for all water heating applications.
UltraSun Premium 300L Direct Solar Hot Water System
Features include:-
•Heavy duty tank which includes a steel powder coated outside casing, steel storage tank internally coated with glazed enamel and fitted with a magnesium sacrificial anode for exceptional corrosion protection, UV resistant plastic end caps and a 2kW heating element with thermostat.
•Solar collectors that incorporate full area copper absorption plates ultrasonically welded to copper circulation tubes, high specification insulation and tempered security glass to provide energy absorption of up to 95%.
•Low thermal conductivity high specification flexible stainless steel circulation piping with silver foil coated polystyrene insulation jackets.
Connection piping that includes an incoming non-return valve, pressure release valve rated at 8bar and drain cock. An extra 3bar pressure release valve is provided for the closed loop tank.
•Galvanised mounting frame for both flat or inclined roof installations that ensures high durability in all weather conditions
Ultrasun Premium solar systems are available in various tank sizes and collector configurations to suit domestic and small-scale installation applications. They are efficient and robust products guaranteed for five years to demonstrate the high material speciation. Designed for many years of trouble free operations, they are the ideal solution for all water heating applications.
UltraSun Standard 200L Direct Solar Hot Water System
Ultrasun Solar hot water systems are economical effective heaters that provide excellent performance,good value and guaranteed long life. They are of Open Loop thermosyphon design with water flow circulating through the collectors and being stored in the tank ready for use. Features include;
•Heavy duty stainless steel AISI 304 tank complete with 2kw electric heater, thermostat and a sacrificial anode to protect against corrosion
•Ultra high efficiency solar collectors incorporating capillary copper pipes ultrasonically welded on a black chrome backplate covered by high transmittance glass• Insulated copper pipe for hot water complete with necessary compression fittings, pressure release valve and a drain cock
•Galvanised mounting frame
Ultrasun Solar water Systems are available in three sizes to suit domestic and small scale institutional applications. They are effective and robust products designed for many years of trouble free operation with a 5 year guarantee to demonstrate product quality
OPERATING CONDITIONS
Water quality: Water outside the following limits should be appropriately pre-treated. Clarity:Clear, TDS:>600mg/l, Hardness:>200mg/l,CaCo3
Saturation Index: >0.8
Max. Operating Temperature: 1500C
Max. Operating Pressure: 6bar
NOTE
Maximum heating output is based on average irradiation levels of 6000W/m2/day prevailing in September – March and minimum Heating output is based on average irradiation levels of 4000W/m2/day prevailing in June/July and are for indicative purposes only.
UltraSun Premium 150L Indirect Solar Hot Water System
Features include:-
•Heavy duty tank which includes a steel powder coated outside casing, steel storage tank internally coated with glazed enamel and fitted with a magnesium sacrificial anode for exceptional corrosion protection, UV resistant plastic end caps and a 2kW heating element with thermostat.
•Solar collectors that incorporate full area copper absorption plates ultrasonically welded to copper circulation tubes, high specification insulation and tempered security glass to provide energy absorption of up to 95%.
•Low thermal conductivity high specification flexible stainless steel circulation piping with silver foil coated polystyrene insulation jackets.
•Connection piping that includes an incoming non-return valve, pressure release valve rated at 8bar and drain cock. An extra 3bar pressure release valve is provided for the closed loop tank.
•Galvanised mounting frame for both flat or inclined roof installations that ensures high durability in all weather conditions
Ultrasun Premium solar systems are available in various tank sizes and collector configurations to suit domestic and small-scale installation applications. They are efficient and robust products guaranteed for five years to demonstrate the high material speciation. Designed for many years of trouble free operations, they are the ideal solution for all water heating applications
MEGASUN SOLAR 300LTR INDIRECT
PROPERTIES
Flexibility of installation
Systems can be either ground-mounted or roof-mounted depending on your requirements. A roof-mounted system can either be coupled or split depending on the aesthetic requirements.
Long lasting
Our water heaters are built to withstand harsh operating conditions, with lifespans of up to 10years or more.
Significant savings
You can save up to 65% on water heating bills!
Environmentally friendly
No emissions or gaseous pollutants.
User-friendly
Easy to install, doesn’t require specific orientation and requires minimal maintenance.
Economical
With 3 to 4 years money-back on the initial amount spent, it is a worthy investment.
MEGASUN SOLAR 300LTR DIRECT
PROPERTIES
Flexibility of installation
Systems can be either ground-mounted or roof-mounted depending on your requirements. A roof-mounted system can either be coupled or split depending on the aesthetic requirements.
Long lasting
Our water heaters are built to withstand harsh operating conditions, with lifespans of up to 10years or more.
Significant savings
You can save up to 65% on water heating bills!
Environmentally friendly
No emissions or gaseous pollutants.
User-friendly
Easy to install, doesn’t require specific orientation and requires minimal maintenance.
Economical
With 3 to 4 years money-back on the initial amount spent, it is a worthy investment.
MEGASUN SOLAR 200LTR INDIRECT
PROPERTIES
Flexibility of installation
Systems can be either ground-mounted or roof-mounted depending on your requirements. A roof-mounted system can either be coupled or split depending on the aesthetic requirements.
Long lasting
Our water heaters are built to withstand harsh operating conditions, with lifespans of up to 10years or more.
Significant savings
You can save up to 65% on water heating bills!
Environmentally friendly
No emissions or gaseous pollutants.
User-friendly
Easy to install, doesn’t require specific orientation and requires minimal maintenance.
Economical
With 3 to 4 years money-back on the initial amount spent, it is a worthy investment.
MEGASUN SOLAR 200LTR DIRECT
The location of a residence or commercial building as well as the quality of water in the area affects the type of system to be installed. The wrong choice of product will affect how well it serves you and how long it lasts. Therefore, you need the right advice.
DIRECT HEATING SYSTEM is designed to heat the water directly, that is, utility water is heated directly in the collector panels.
MEGASUN SOLAR 120LTR INDIRECT
The location of a residence or commercial building as well as the quality of water in the area affects the type of system to be installed. The wrong choice of product will affect how well it serves you and how long it lasts. Therefore, you need the right advice.
INDIRECT HEATING SYSTEM:is designed to be used where water is corrosive or hard. They use a heat exchange method with glycol to heat water. Efficiencies are similar to a direct system. Indirect Solar water systems are especially applicable in alkaline areas such as the Rift Valley and Coastal regions or those areas that predominantly use borehole water.
MEGASUN SOLAR 120 LTR DIRECT
The location of a residence or commercial building as well as the quality of water in the area affects the type of system to be installed. The wrong choice of product will affect how well it serves you and how long it lasts. Therefore, you need the right advice.
DIRECT HEATING SYSTEM is designed to heat the water directly, that is, utility water is heated directly in the collector panels
PROPERTIES
Flexibility of installation
Systems can be either ground-mounted or roof-mounted depending on your requirements. A roof-mounted system can either be coupled or split depending on the aesthetic requirements.
Long lasting
Our water heaters are built to withstand harsh operating conditions, with lifespans of up to 10years or more.
Significant savings
You can save up to 65% on water heating bills!
Environmentally friendly
No emissions or gaseous pollutants.
User-friendly
Easy to install, doesn’t require specific orientation and requires minimal maintenance.
Economical
With 3 to 4 years money-back on the initial amount spent, it is a worthy investment.